Alarm Pengendali Asap Pada Ruangan Bebas Asap Berbasis Mikrokontroler Arduino

Authors

  • Winarno Fadjar Bastari Program Studi Teknik Elektro, Fakultas Teknik, Universitas PGRI Adi Buana Surabaya
  • Akhmad Solikin Program Studi Teknik Elektro, Fakultas Teknik, Universitas PGRI Adi Buana Surabaya
  • Widodo Widodo Program Studi Teknik Elektro, Fakultas Teknik, Universitas PGRI Adi Buana Surabaya

DOI:

https://doi.org/10.30736/je-unisla.v7i1.818

Keywords:

Smoke, sensor, MQ2, Arduino, pollution.

Abstract

Smoke is air pollution that is very dangerous for human health. Therefore, in this study the authors designed and modeled a fan speed controller using a smoke sensor based on an Arduino microcontroller. In addition, smoke control alarms can also be used for monitoring in smoke-free rooms in order to prevent and at the same time provide a deterrent effect on people who smoke in places where smoking is prohibited. The method used is to process the data detected by the MQ2 smoke sensor, then display the amount or level of smoke in the room and its condition on the LCD/monitor. The comparison of the values on the sensor will be processed with the Arduino and the output of the Arduino will be input coding on the Arduino IDE software to control the fan speed performance as a response to exhaust air in the ventilation area of the room. The microcontroller process is in the program as a controller of all components, then coding will control all components according to the coding ordered in the microcontroller and voltage controller at the smoke sensor input and LCD and fan output. The results obtained from this research project are able to detect the state of the air in a smoke-free room from smoke and CO pollution from 0 ppm to = 256 ppm and this pollution can be reduced by adjusting the fan speed as room air ventilation to avoid the deposition of smoke in a smoke-free room. which is dangerous. So that the air in the room becomes cleaner and safer for health.

Downloads

Download data is not yet available.

References

Abdullah E. 2010. Rancang Bangun Pengatur Kecepatan Kipas Pembuangan Menggunakan Sensor Asap Af30 Berbasis Mikrokontroler Atmega8535. Universitas Diponegoro Semarang.

Albahri, Fahad. 2014. Pendeteksi Asap Rokok Untuk Lingkungan Bebas Asap Rokok Berbasis Mikrokontroler ATMega32U4. Sekolah Tinggi Manajemen dan Ilmu Komputer Raharja. Albahri, Fahad. 2014.

Pendeteksi Asap Rokok Untuk Lingkungan Bebas Asap Rokok Berbasis Mikrokontroler ATMega32U4. Sekolah Tinggi Manajemen dan Ilmu Komputer Raharja.

C. E. Widodo, Winarto, dan Sumariyah.“Pembuatan alat pendeteksi kebakaran dengan detektor asapâ€, Jurnal Berkala Fisika 6 (3), 51-54 (2003).

Datasheet Sensor Gas Dan Asap MQ-2 2010, Diakses 25 Oktober 2012, Dari http://www.seeedstudio.com/depot/data sheet/MQ-2.pdf No Ruangan Sensor MQ-2 Tegangan Sensor MQ-2 Ketika Tidak Ada Asap Tegangan Sensor MQ2 Ketika Ada Asap Sensor MQ-2 Di Ruangan 1 4,1 Volt 4,2 - 4,4 Volt Sensor MQ-2 Di Ruangan 2 4,1 Volt 4,2 - 4,4 Volt.

Faishal, A., Budiyanto, M., (2010). “Pendeteksi Kebakaran Dengan Menggunakan Sensor Suhu LM35D Dan Sensor Asapâ€, Seminar Nasional Informatika, UPN “Veteranâ€.

Fajri Septria Agung. 2012. Sistem Deteksi Asap Rokok pada Ruangan Bebas Asap Rokok dengan Keluaran juara.Teknik Komputer. AMIK GI MDP.

M Aldi F. 2013. Perancangan dan Pembuatan Alat Pengurai Asap Rokok pada Smoking Room Menggunakan Kontroler PID. Universitas Brawijaya.

Moch. Rifai Syambera. 2014. Pengertian dari sensor asap mq-2 menurt ahli. Teknik Elektronika, Universitas Politeknik Negeri Semarang.

M Hudi. 2012. Rancang Bangun Sistem Pengendali Kadar Asap Pada Smoking Area Berbasis Mikrokontroler Atmega 8535. Universitas Pembangunan Nasional "Veteran" Jawa Timur.

PlumX Metrics

Published

12-04-2022

How to Cite

Bastari, W. F., Solikin, A., & Widodo, W. (2022). Alarm Pengendali Asap Pada Ruangan Bebas Asap Berbasis Mikrokontroler Arduino. JE-Unisla, 7(1), 32–35. https://doi.org/10.30736/je-unisla.v7i1.818

Issue

Section

editorial elektro

Most read articles by the same author(s)