Upper Structure of Precast Concretes Comparison: PC-I and PC-U in West Outer Ring Road, Surabaya
DOI:
https://doi.org/10.30736/cvl.v7i2.882Abstract
Increasing of motorcycle numbers in big cities in Indonesia, especially in Surabaya. The traffic becomes crowded and road capacity is exceeded. Because of the increasing of motorcycle volume, especially in western part of Surabaya, the government built a flyover in west outer ring road to provide solution to congestion in Surabaya. This study aimed to determine the comparation between PC-I girder and PC-U girder used. In west outer ring road, the method was used to calculate prestressed beam was fully prestressed. The researcher reviewed the prestressed beam from behavior, reaction, and impact to the all of bridge structures from structure. The Software SAP 2000 V.14.2.5 is used to structure calculation analysis. According to analysis result, the calculation has been carried out, the difference ratio of the bridge floor slabs was studied. Flyover model with PC-U prestressed beam had smaller ratio than PC-I. The comparison of strand used in PC-U beams was more than PC-I with 42.22%. The maximum moment value was occurred in PC-I girder beam was 1541.979 Tons.meter and PC-U girder was 2252.599 Tons.meter. The strand requirements and cross area section was comparised too.
Downloads
References
T. A. Aprianto and K. H. Putra, “ANALISIS FORECASTING METHOD PERTUMBUHAN LALU LINTAS PADA RUAS JALAN ACHMAD YANI SURABAYA,†pp. 54–60.
I. Hidayat, “ANALISIS PERHITUNGAN JEMBATAN GELAGAR I PADA JEMBATAN JALAN RAYA DAN JEMBATAN KERETA API Metode Perhitungan,†no. 9, pp. 517–528, 1921.
B. P. Putra et al., “STUDI PERBANDINGAN PENGGUNAAN PCU GIRDER DAN PCI GIRDER,†vol. XXII, no. 1, 2017.
N. B. Tiburzi, T. Drimalas, and K. J. Folliard, “Cement and Concrete Research Evaluation of precast bridge girder cracking : The role of volume change,†Cem. Concr. Res., vol. 101, no. September, pp. 55–67, 2017, doi: 10.1016/j.cemconres.2017.08.024.
M. Alawneh and M. K. Tadros, “Optimized ultra-high-performance concrete horizontally curved bridge superstructure,†no. April, 2022.
A. P. Astuti, T. P. Artiningsih, and I. Pendahuluan, “ANALISIS PERBANDINGAN PCI GIRDER TERHADAP PCU GIRDER EXISTING,†pp. 1–7.
S. N. Indonesia and B. S. Nasional, “Pembebanan untuk jembatan,†2016.
G. J. Perkotaan, “Geometri Jalan Perkotaan,†2004.
S. T. Side, “ANALYSIS COMPARISON LOSS OF PRESSTRES,†vol. XII, no. 1, pp. 1–7, 2020.
M. N. Sholeh and U. Diponegoro, “Design of Sustainable Construction Through Value Engineering of an Design of Sustainable Construction Through Value Engineering of an Automated People Mover System Project,†no. April, 2020, doi: 10.1088/1755-1315/448/1/012060.
H. Prayuda et al., “Pengaruh Modifikasi Penampang pada I - Girder dan Box Girder Beton Prategang terhadap Kekakuan dan Lendutan,†vol. 27, no. 1, pp. 97–106, 2021.
J. Zhang, Y. Jing, P. Li, W. Han, N. Zhang, and Y. Zhou, “Experimental and Numerical Investigation on the Ultimate Vertical Bearing Capacity of U-Shaped,†2019.
J. Ilmiah, T. Sipil, P. N. Samarinda, J. T. Sipil, P. N. Samarinda, and K. Timur, “ANALISA DESAIN PC I GIRDER PADA SECTION OVERPASS,†vol. 13, no. 1, pp. 25–35, 2021.
B. Massicotte and N. Cordoni, “Design of precast prestressed SFRC T-girders for accelerated sustainable bridge construction 1 Introduction,†pp. 195–204.
I. Bridges et al., “Evaluation of Cast-in-Place Splice Regions of Spliced,†no. 116, pp. 181–194, 2019, doi: 10.14359/51716804.
B. C. Jagtap and P. M. Shahezad, “Comparative Study of Prestressed Concrete Girder and Steel Plate Girder for Roadway Over Bridge,†vol. 2, no. 1, pp. 113–117, 2016.
S. Rana, R. Ahsan, and S. N. Ghani, “Design of prestressed concrete I-girder bridge superstructure using opti- mization algorithm,†pp. 978–984, 2010.
V. U. Misal, N. G. Gore, and P. J. Salunke, “Analysis and Design of Prestressed Concrete Girder,†no. 9, pp. 43–47, 2014.
I. Yamin and S. Zuraida, “Analisis Perbandingan Kehilangan Prategang Akibat Variasi Letak Tendon PC I Girder Jembatan Beton Prategang,†vol. 2, no. 2, pp. 34–42, 2020.
R. T--, “IcoT UST 2018 - Teknik Sipil UST IcoT UST 2018 - Teknik Sipil UST,†vol. 2016, no. 2008, pp. 31–34, 2016.
Downloads
Published
How to Cite
Issue
Section
License
Authors who publish in this journal agree to the following terms:
-
- Copyright on any article is held by the author.
- The author grants the journal first publication rights with the work licensed concurrently under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of authorship and initial publication of the work in this journal.
- Authors may make separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of that journal (for example, posting it to an institutional repository or publishing it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (for example, in an institutional repository or on their website) before and during the submission process, as doing so can lead to productive exchange, as well as earlier and greater citation of the published work.
- Published articles and related materials distributed under a Creative Commons Attribution-ShareAlike 4.0 International License
Civilla (Jurnal Teknik Sipil Universitas Islam Lamongan) by Universitas Islam Lamongan is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Based on a work at https://jurnalteknik.unisla.ac.id/index.php/CVL/index
