The Effect of Hot Sun on the Compressive Strength of Concrete on the Sukoharjo – Hargosari Road Section

Putri Regina Wigatiningrum; Tantin Pristyawati; Marwahyudi; Dian Muhammad Rifai; Muhammad Yusuf Arifin

doi:10.30736/cvl.v10i1.1319

Authors

Putri Regina Wigatiningrum Universitas Veteran Bangun Nusantara Sukoharjo
Tantin Pristyawati Universitas Veteran Bangun Nusantara Sukoharjo
Marwahyudi Universitas Sahid Surakarta
Dian Muhammad Rifai Universitas Sahid Surakarta
Muhammad Yusuf Arifin Universitas Sahid Surakarta

DOI:

https://doi.org/10.30736/cvl.v10i1.1319

Keywords:

Concrete, concrete compressive strength, hammer test, solar heat

Abstract

This study discusses how much influence the hot sun has on the strength of concrete. Concrete is widely used in construction, because it is cheap and easy to implement. Still, it also requires extensive knowledge regarding the nature of the basic concrete material, how to make it, and when to lay it so that it can produce maximum quality and quality when the concrete is laidThe research aims to find out how much influence the hot sun during casting has on the compressive strength of concrete. In this research, test specimens were made for the concrete mixture with a design compressive strength of f'c = 20 MPa, using a cylinder with a diameter of 15 cm and a height of 30 cm, and strength testing. press approach using hammer test. Casting was carried out in the morning, afternoon, and evening with different types of sunlight on one road section. The results of this research show that the hot sun during casting affects the compressive strength of the concrete produced. The heat of the sun is too hot, causing the concrete that is laid to crack easily and its compressive strength is low even though the concrete has been covered with geoteck and watered regularly.

Downloads

References

J. Liu et al., “Experimental analysis on water penetration resistance and micro properties of concrete: effect of supplementary cementitious materials, seawater, sea-sand and water-binder ratio,” J. Build. Eng., vol. 50, p. 104153, 2022, doi: 10.1016/j.jobe.2022.104153.

S. Winarto, A. I. Candra, E. Siswanto, and R. Ajiono, “Analysis Causes damage and prevention of concrete,” in Journal of Physics: Conference Series, IOP Publishing, 2020, p. 42031. doi: 10.1088/1742-6596/1569/4/042031.

Y. Andika, I. T. Saputro, and O. Bonde, “Studi Eksperimantal Kuat Tekan Beton Menggunakan Material Dari Kali Jodoh,” J. Karkasa, vol. 7, no. 1, pp. 22–27, 2021, doi: 10.32531/jkar.v7i1.372.

A. T. Dachlan and R. Setiady, “PEMANFAATAN PASIR MERAPI UNTUK BETON MUTU TINGGI,” J. Jalan Jemb., vol. 32, no. 1, pp. 16–31, 2015.

M. D. J. Sumajouw, S. O. Dapas, and R. S. Windah, “Pengujian Kuat Tekan Beton Mutu Tinggi,” J. Ilm. Media Eng., vol. 4, no. 4, 2014.

M. Alifsyah, M. Jamal, and T. S. P. Arifin, “ANALISA KUAT TEKAN BETON MENGGUNAKAN METODE COMPRESSION TEST DAN HAMMER TEST MENGGUNAKAN AGREGAT HALUS PASIR TENGGARONG,” J. Ilmu Pengetah. dan Teknol., vol. 7, no. 1, 2023.

M. Ichsan, D. Tanjung, and M. H. M. Hasibuan, “Analisa Perbandingan Hammer Test dan Compression Testing Machine terhadap Uji Kuat Tekan Beton,” Bul. Utama Tek., vol. 17, no. 1, pp. 41–45, 2021.

Yulianto A, “Peranan Ilmu Komputer Dalam Perhitungan Uji Beton Di Laboratorium Marwahyudi,” Gaung Inform., vol. Vol 6 No 1, no. 0271, pp. 35–52, 2013.

M. Marwahyudi, “Tegangan Geser Batu Bata Berkonstruksi Pada Dinding Rumah Rawan Gempa,” Astonjadro, vol. 8, no. 2, p. 80, 2020, doi: 10.32832/astonjadro.v8i2.2725.

Standar Nasional Indonesia, “Cara uji kuat tekan beton dengan benda uji silinder,” Badan Standarisasi Nasional, Jakarta, 1974.

G. Genial and V. Violintina, “Pembuatan Ultra High Strength Concrete Dengan Material Lokal,” J. Dimens. Pratama Tek. Sipil, vol. 1, no. 1, 2012.

SNI 03-2834-2000, SNI 03-2834-2000: Tata cara pembuatan rencana campuran beton normal. SNI 03-2834-2000, 2000.

P. G. Quedou, E. Wirquin, and C. Bokhoree, “A sustainable approach in using construction and demolition waste materials in concrete,” World J. Eng., vol. 18, no. 6, pp. 826–840, 2021, doi: 10.1108/WJE-05-2020-0161.

A. Maharani and A. Rochman, “Pengaruh Bahan Tambah Plastiment Vz terhadap Kuat Tekan Beton untuk Grouting pada Proyek Pembangunan Manyar Smelter Desalination Plant-Gresik,” JIM J. Ilm. Mhs. Pendidik. Sej., vol. 8, no. 3, pp. 3076–3082, 2023, doi: 10.24815/jimps.v8i3.26398.

Ernawati, Tumingan, and B. Nugroho, “Evaluasi Kuat Tekan Beton Menggunakan Hammer Test Dan Ultrasonic Pulse Velocity (Upv) Pada,” J. Ilm. Tek. Sipil Politek. Negeri Samarinda, vol. 14, no. 1, pp. 16–22, 2022.

A. Maysyurah, A. Rusdi, and A. Didik Setyo Purwantoro, “Compressive Strength Of Concrete The Time Setting Of Application Of Plastiment® P-121 Additive Mixture,” Civilla J. Tek. Sipil Univ. Islam Lamongan, vol. 9, no. 1, pp. 39–46, 2024, doi: 10.30736/cvl.v9i1.1185.

C. ASTM, “805, Standard test method for rebound number of hardened concrete,” West Conshohocken, USA, 2008.

H. Rahmani and A. Gazali, “Pengaruh Suhu Bahan Campuran Terhadap Sifat dan Mutu Beton Dalam Pelaksanaan Drainase Jalan pada Daerah Terpencil di Provinsi Kalimantan Selatan,” J. Manaj. Aset Infrastruktur Fasilitas, vol. 3, 2019.

A. Alkhamuddin and A. Adiguna, “Simulasi Perubahan Kuat Tekan Beton Pada Kondisi Ekstrim Pasca Pembakaran,” J. Deform., vol. 3, no. 2, pp. 115–121, 2018.

A. Aminullah, “Uji Kekuatan Mutu Beton Terhadap Pengaruh Cuaca Pada Variasi Waktu Tertentu Dalam Perlakuan Pada Sampel Kubus Sisi 15 Cm,” J. Kacapuri J. Keilmuan Tek. Sipil, vol. 3, no. 2, pp. 196–208, 2020.

R. Riduan, “Pengaruh Suhu Agregat Kasar Terhadap Kekuatan Beton Mutu Sedang Untuk Konstruksi Jalan.” Universitas Islam Riau, 2021.

A. Zakariya, G. Yudhono, and S. Rosyadi, “Kajian Temperatur Beton Saat Proses Pengerasan Menggunakan Fly Ash Sebagai Bahan Tambah Semen,” J. Jalan Jemb., vol. 38, no. 2, pp. 108–117, 2021.