Pengaruh Metode Perawatan Beton Dengan Suhu Normal Terhadap Kuat Tekan Beton Mutu Tinggi
DOI:
https://doi.org/10.30736/cvl.v5i2.492Keywords:
Beton Mutu Tinggi, Kuat Tekan, Perawatan BetonAbstract
Pembangunan infrastruktur menjadi hal yang sedang digadang-gadang dalam pemerintahan era sekarang. Salah satu pembangunan yang berkembang adalah bidang konstruksi. Beton menjadi material yang penting dalam konstruksi. Kualitas beton menjadi fokus utama yang perlu diperhatikan. Pada konstruksi, material beton mutu tinggi menjadi hal yang pokok digunakan. Selain kualitas material penyusun, metode pelaksanaan perawatan beton juga menjadi hal yang berpengaruh. Penelitian ini bertujuan untuk mengetahui bagaimana pengaruh cara perawatan beton dengan suhu normal terhadap kuat tekan beton mutu tinggi . Metode eksperimental dan studi literatur digunakan pada penelitian ini Benda uji yang digunakan berbentuk silinder dengan tinggi 30 cm dan berdiameter 15 cm dengan mutu awal beton 36,6 Mpa. Variasi yang digunakan adalah cara perawatan beton ( tanpa perawatan, perawatan direndam, perawatan disiram,) . Pengujian kuat tekan dilakukan saat umur beton 28 hari. Hasil penelitian menunjukkan bahwa kuat tekan tertinggi didapat dengan metode perawatan direndam dengan nilai kuat tekan yaitu 38,15 Mpa.SDownloads
References
:2011, SNI. 2011. “SNI 1974:2011 Tentang Cara Uji Kuat Tekan Beton Dengan Benda Uji Silinder.†Badan Standardisasi Nasional: 20.
ASTM, C.494. 2001. “Standard Specification for Chemical Admixtures for Concrete 1.†04: 1–9.
ASTM C33. 2003. “Standard Specification for Concrete Aggregates.†ASTM International i(C): 11.
Cahyo, Y., A. I. Candra, E. Siswanto, and A. Gunarto. 2020. “The Effect of Stirring Time and Concrete Compaction on K-200 Concrete Press Strength.†Journal of Physics: Conference Series 1569(4).
Candra, A. I., A. Ridwan, S. Winarto, and Romadhon. 2020. “Correlation of Concrete Strength and Concrete Age K-300 Using Sikacim® Concrete Additive and Master Ease 5010.†Journal of Physics: Conference Series 1569(4).
Candra, Agata Iwan, Heri Wahyudiono, Sulik Anam, and Dwifi Aprillia. 2020. “KUAT TEKAN BETON Fc ’ 21 , 7 MPa MENGGUNAKAN WATER REDUCING AND HIGH RANGE ADMIXTURES.†Jurnal CIVILA 5(1): 330–40.
Gagg, Colin R. 2014. “Cement and Concrete as an Engineering Material: An Historic Appraisal and Case Study Analysis.†Engineering Failure Analysis 40: 114–40.
Gardjito, Edy, Agata Iwan Candra, and Yosef Cahyo. 2018. “Pengaruh Penambahan Batu Karang Sebagai Substitusi Agregat Halus Dalampembuatan Paving Block.†UKaRsT 2(1): 35.
Husni, Muhammad, and Malik Hasibuan. 2019. “Pengaruh Cara Dan Lama Perawatan Terhadap Kuat Tekan Beton.†14(2).
Ir. Mulyono Sadyohutomo, MCRP. 2018. “Pembangunan Berkelanjutan (Sustainable Development).â€
Iskandar, Yunike Dwi. 2020. “Pengaruh Metode Perawatan Beton Terhadap Kuat Tekan Beton Normal.†Jurnal Teknik Sipil ITP 7(2): 145.
Iwan, Agata, and Eko Siswanto. 2018. “MENGGUNAKAN HYDROTON DAN MASTER EASE 5010.†3(2): 162–65.
Kartika, Chandra. 2005. “PENGARUH STANDARD PRODUCT, QUALITY ASSURANCE, COMPETITIVE PRICE DAN DELIVERY ON TIME TERHADAP KEPUASAN PELANGGAN DAN LOYALITAS PELANGGAN PRODUK BETON PRACETAK (STUDI KASUS DI PT. TJAKRINDO MAS – GRESIK ).†NASPA Journal 42(4): 1.
Kaufmann, Josef. 2020. “Evaluation of the Combination of Desert Sand and Calcium Sulfoaluminate Cement for the Production of Concrete.†Construction and Building Materials 243: 1–10.
Li, Zhen, Jiaping Liu, Jianzhuang Xiao, and Peihua Zhong. 2020. “Internal Curing Effect of Saturated Recycled Fine Aggregates in Early-Age Mortar.†Cement and Concrete Composites 108: 103444. https://doi.org/10.1016/j.cemconcomp.2019.103444.
Mohammed Ali, Ahmed A., Roua Suhail Zidan, and Tuqa Waleed Ahmed. 2020. “Evaluation of High-Strength Concrete Made with Recycled Aggregate under Effect of Well Water.†Case Studies in Construction Materials 12: e00338. https://doi.org/10.1016/j.cscm.2020.e00338.
Moses Hasiholan Septian Tampubolon, dan Torang Sitorus. “REKAYASA EKSPERIMEN BETON DENGAN PENAMBAHAN ADITIF MASTERSURE 1007 UNTUK MENDAPATKAN BETON SLUMP FLOW YANG STABIL PADA BETON DENGAN MUTU AWAL TINGGI.â€
Ngwenya, Legae M, and Shodolapo Oluyemi Franklin. 2015. “Influence of Recycled Coarse Aggregate on Some Properties of Fresh and Hardened Concrete.†International Journal of Innovative Science, Engineering & Technology 2(12): 257–64.
Okonkwo, V O, and Arinze Emmanuel E. 2018. “A Study of the Effect of Aggregate Proportioning On Concrete Properties.†American Journal of Engineering Research ( AJER ) 7(4): 61–67.
R H M Rum, Z M Jaini, N H Abd Ghaffar, N Abd Rahman. 2017. “A Preliminary Experimental Study on Vibration Responses of Foamed Concrete Composite Slabs.†IOP Conference Series: Materials Science and Engineering 271: 1–8.
Ralph O. Lane. 1998. “Behavior of Fresh Concrete During Vibration.†Manual of concrete practice: 1–19.
Safawi, Mohammad Ibrahim, Ichiro Iwaki, and Takashi Miura. 2005. “A Study on the Applicability of Vibration in Fresh High Fluidity Concrete.†Cement and Concrete Research 35(9): 1834–45.
Shane, Tymkowicz, and Robert Steffes. 1999. Vibration Study for Consolidation of Portland Cement.
SNI 03-6805-2002. 2002. “Metode Pengujian Untuk Mengukur Nilai Kuat Tekan Beton Pada Umur Awal Dan Memproyeksikan Kekuatan Pada Umur Berikutnya.†Badan Standardisasi Nasional.
SNI 1972:2008. 2008. “Cara Uji Slump Beton.â€
SNI 2493:2011. 2011. “Tata Cara Pembuatan Dan Perawatan Benda Uji Beton Di Laboratorium.†Standar Nasional Indonesia: 23.
Sumaryoto. 2010. “Dampak Keberadaan Jalan Tol Terhadap Kondisi Fisik, Sosial, Dan Ekonomi Lingkungannya.†Journal of Rural and Development 1(2): 161–68.
Supriani, Fepy, and Mukhlis Islam. 2019. “Pengaruh Metode Perlakuan Dalam Perawatan Beton Terhadap Kuat Tekan Dan Durabilitas Beton.†Inersia, Jurnal Teknik Sipil 9(2): 47–54.
Ueno, Atsushi, and Yuko Ogawa. 2020. “Influence of Coarse Aggregate Shape on Optimum Fine to Total Aggregate Ratio Using a Virtual Voids-Ratio Diagram in Concrete Compaction.†Cement and Concrete Composites 106: 103463.
Winarto, S., A. I. Candra, E. Siswanto, and R. Ajiono. 2020. “Analysis Causes Damage and Prevention of Concrete.†Journal of Physics: Conference Series 1569(4).
Zahid, Muhammad, Nasir Shafiq, and Asif Jalal. 2018. “Investigating the Effects of Solarcure Curing Method on the Compressive Strength, Microstructure and Polymeric Reaction of Fly Ash Based Geopolymer.†Construction and Building Materials 181: 227–37. https://doi.org/10.1016/j.conbuildmat.2018.06.046.
Zeyad, Abdullah M. 2019. “Effect of Curing Methods in Hot Weather on the Properties of High-Strength Concretes.†Journal of King Saud University - Engineering Sciences 31(3): 218–23. http://dx.doi.org/10.1016/j.jksues.2017.04.004.
Zhao, Jing, Yiran Yang, and Lin Li. 2020. “A Comprehensive Evaluation for Different Post-Curing Methods Used in Stereolithography Additive Manufacturing.†Journal of Manufacturing Processes 56(May 2019): 867–77. https://doi.org/10.1016/j.jmapro.2020.04.077.
Downloads
Published
How to Cite
Issue
Section
License
Authors who publish in this journal agree to the following terms:
-
- Copyright on any article is held by the author.
- The author grants the journal first publication rights with the work licensed concurrently under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of authorship and initial publication of the work in this journal.
- Authors may make separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of that journal (for example, posting it to an institutional repository or publishing it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (for example, in an institutional repository or on their website) before and during the submission process, as doing so can lead to productive exchange, as well as earlier and greater citation of the published work.
- Published articles and related materials distributed under a Creative Commons Attribution-ShareAlike 4.0 International License
Civilla (Jurnal Teknik Sipil Universitas Islam Lamongan) by Universitas Islam Lamongan is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Based on a work at https://jurnalteknik.unisla.ac.id/index.php/CVL/index
