Comparison of the Effectiveness of Immersion Curing and Burlap Sacks Curing on the Compressive Strength of Concrete with Superplasticizers
DOI:
https://doi.org/10.30736/cvl.v11i1.1599Keywords:
Concrete, Curing, Compressive Strength, AdditivesAbstract
This study aims to examine the effectiveness of two concrete treatment methods with SikaCim superplasticizer on concrete compressive strength. The curing method was used by immersion in water and covering the concrete surface with wet gunny sacks. The compressive strength test was conducted when the concrete was 28 days old. The concrete used is normal concrete and normal concrete with additives. This study tested concrete with 24 cylindrical specimens (15 cm x 30 cm). The results of the concrete compressive strength study show that the values of normal concrete soaked in water, with normal concrete covered with burlap sacks shows an increase of 30.6%. For comparison, the concrete treatment of added superplasticizer soaked in water, with the concrete added superplasticizer covered with burlap sacks, increased by 25.4%. The conclusion is that the highest compressive strength occurs in concrete with superplasticizer additives, with treatment covered with wet burlap sacks, which is 25.57 MPa.
Downloads
References
[1] R. R. S. Riwayati and R. Habibi, “Pengaruh Penambahan Zat Aditif Sika Viscocrete Terhadap Kuat Tekan Mutu Beton K-300 Umur 14 Hari,” Jurnal Tekno Global UIGM Fakultas Teknik, vol. 9, no. 2, 2021, doi: 10.36982/jtg.v9i2.1293.
[2] S. Permatasari and K. Bintang, “Pengaruh Bahan Tambah Sika Viscocrete (1003) Terhadap Kuat Tekan Beton f’c 20 MPa Menggunakan Agregat Kasar Dan Agregat Halus Di Kabupaten Kotabaru,” TAPAK, vol. 10, no. 1, 2020.
[3] R. Sitanggang, N. S. Hutabarat, and R. Ginting, “PENGGUNAAN SUPERPLASTICIZER PADA BETON MUTU F’c 25 MPa,” JURNAL ILMIAH TEKNIK SIPIL, vol. 11, no. 2, 2022, doi: 10.46930/tekniksipil.v11i2.2707.
[4] I. Trisnawati, W. H. Hidayat, A. Ismail, and K. Korizon, “Analisa Kuat Tekan Beton K 300 Dengan Penambahan SikaCim Concrete,” Jurnal Teknik Sipil, vol. 13, no. 2, 2024, doi: 10.36546/tekniksipil.v13i2.1084.
[5] D. N. E. Al Munawar and E. Widyaningsih, “Pengaruh Additive Sikacim Concrete terhadap Kuat Tekan Beton Normal,” Prosiding FTSP Series 2024, 2024.
[6] O. T. R. Zai, “PENGARUH PENGGUNAAN BAHAN TAMBAH DAMDEX,” Bandung, 2023. Accessed: Nov. 29, 2025. [Online]. Available: https://elibrary.unikom.ac.id/id/eprint/8898/
[7] D. H. Darayani, T. Tavio, I. G. P. Raka, and P. Puryanto, “The Effect of Styrofoam Artificial Lightweight Aggregate (ALWA) on Compressive Strength of Self Compacting Concrete (SCC),” Civil Engineering Journal, vol. 4, no. 9, p. 2111, Sep. 2018, doi: 10.28991/cej-03091143.
[8] D. Renjani Putra, “PENGARUH PENAMBAHAN KAWAT BENDRAT PADA CAMPURAN BETON TERHADAP KUAT TEKAN,” 2021.
[9] V. Fernando, E. Hunggurami, and T. M. W. Sir, “Pengaruh Perawatan Beton (Curing) menggunakan Water Curing dan Membrane Curing terhadap Kuat Tekan Beton,” Jurnal Teknik Sipil, vol. 12, no. 2, 2023.
[10] T. Purnomo Adi, “PENGARUH PERAWATAN BETON (CURING) TERHADAP KUAT TEKAN BETON NORMAL,” JITSi : Jurnal Ilmiah Teknik Sipil, vol. 3, no. 2, 2023, doi: 10.36423/jitsi.v3i2.1489.
[11] E. Erlina and C. K. Permatasari, “PENGARUH CURING MENGGUNAKAN AIR SUNGAI DAN AIR SUMUR TERHADAP KUAT TEKAN BETON,” CivETech, vol. 6, no. 1, 2024, doi: 10.47200/civetech.v6i1.2243.
[12] D. S. Nugroho et al., “Penggunaan Limbah Hasil Pembakaran Batu Bara dan Sugar Cane Bagasse Ash (SCBA) pada Paving Geopolimer dengan Proses Steam Curing,” vol. 4, no. 2, 2015.
[13] H. Hamada, A. Alattar, B. Tayeh, F. Yahaya, and I. Almeshal, “Influence of different curing methods on the compressive strength of ultra-high-performance concrete: A comprehensive review,” Case Studies in Construction Materials, vol. 17, Dec. 2022, doi: 10.1016/j.cscm.2022.e01390.
[14] B. R. Machado, L. S. Silva, M. Amario, A. N. Haddad, A. S. de Vargas, and C. M. Stolz, “Effect of curing methods on the long-term properties of concrete containing crystallizing additives,” Next Materials, vol. 8, Jul. 2025, doi: 10.1016/j.nxmate.2025.100759.
[15] A. Kumar, G. J. Singh, B. L. Chauhan, and R. Kumar, “Curing sensitivity and rational curing period for recycled aggregate concrete,” CEMENT, vol. 24, p. 100175, Jun. 2026, doi: 10.1016/j.cement.2026.100175.
[16] M. Davraz, N. Isildar, and A. N. Kaplan, “Investigation of the effects of steam curing of concrete at different temperatures on cost and compressive strength by response surface methodology,” Constr. Build. Mater., vol. 470, Apr. 2025, doi: 10.1016/j.conbuildmat.2025.140589.
[17] C. Cremonez, J. Maria McCartney da Fonseca, A. Carolina Seguro Cury, E. Otto Ferreira, and W. Mazer, “Analysis of the influence of the type of curing on the axial compressive strength of concrete,” Mater. Today Proc., vol. 58, pp. 1211–1214, Jan. 2022, doi: 10.1016/j.matpr.2022.01.430.
[18] A. Ridwan, Y. Cahyo Setianto Poernomo, and E. Garjito, “Analysis of Concrete Strength Analysis K-250 With Additional Asbestos Waste Powder as a Substitute of Fine Aggregate,” Jurnal Teknik Sipil Universitas Islam Lamongan, vol. 09, no. 1, pp. 109–118, 2024, doi: 10.30736/cvl.v2i2.
[19] K. Tjokrodimuljo, “Teknologi Beton, Buku Ajar,” Jurusan Teknik Sipil–Magister Teknologi Bahan Bangunan–Universitas Gadjah Mada, Yogyakarta, Yogyakarta, 2007.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2026 Dhiafah Hera Darayani, Juanita, Hafiz Hamdani, Cindrawati
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Authors who publish in this journal agree to the following terms:
-
- Copyright on any article is held by the author.
- The author grants the journal first publication rights with the work licensed concurrently under a Creative Commons Attribution License that allows others to share the work with an acknowledgment of authorship and initial publication of the work in this journal.
- Authors may make separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of that journal (for example, posting it to an institutional repository or publishing it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (for example, in an institutional repository or on their website) before and during the submission process, as doing so can lead to productive exchange, as well as earlier and greater citation of the published work.
- Published articles and related materials distributed under a Creative Commons Attribution-ShareAlike 4.0 International License
Civilla (Jurnal Teknik Sipil Universitas Islam Lamongan) by Universitas Islam Lamongan is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Based on a work at https://jurnalteknik.unisla.ac.id/index.php/CVL/index
